Machine Work

131 topics in this forum

1. Takedown 98'

   By slseacrist, January 20, 2007
   • 24 replies
   • 9.8k views
   • 
   • slseacrist
   • April 27, 2007

2. Mig Welding?

   By CTI, January 17, 2009
   • 23 replies
   • 6.7k views
   • 
   • FC
   • April 25, 2010

3. Re-Rifling

   By farmall, August 30, 2005
   • 22 replies
   • 3.2k views
   • 
   • AzRednek
   • September 26, 2005

4. Where to go from here

   By bubbamauser, October 10, 2005
   • 21 replies
   • 2.1k views
   • 
   • Pedestal
   • October 13, 2005

5. Another Lathe Question

   By scott63, April 6, 2007
   • 21 replies
   • 3.2k views
   • 
   • scott63
   • April 14, 2007

6. Rechamber 8mm m98 to 325 wsm ?

   By asmart, August 14, 2005
   • 20 replies
   • 5.3k views
   • 
   • z1r
   • August 18, 2005

7. Inner torque shoulder out of square

   By mcassill, October 25, 2005
   • 20 replies
   • 1.8k views
   • 
   • mcassill
   • October 31, 2005

8. The Glorious Mini-lathe

   By Doble Troble, December 27, 2006
   • 19 replies
   • 7.2k views
   • 
   • Doble Troble
   • January 8, 2007

9. Removing Mauser Charger Guide

   By Clemson, February 6, 2006
   • 17 replies
   • 5.8k views
   • 
   • Guest
   • February 10, 2006

10. Rem 700 Barrel On A Turk?

    By Kyle, October 24, 2006
    • 17 replies
    • 2k views
    • 
    • ken98k
    • November 13, 2006

11. Fitting Barrel To A Large Ring Receiver?

    By Kyle, December 19, 2006
    • 17 replies
    • 2.3k views
    • 
    • donmarkey
    • December 23, 2006

12. Tang Extension

    By donmarkey, February 16, 2009
    • 17 replies
    • 3.3k views
    • 
    • AzRednek
    • February 27, 2009

13. Hand reaming a short chambered barrel

    By montea6b, October 2, 2005
    • 16 replies
    • 2.1k views
    • 
    • montea6b
    • October 28, 2005

14. Oxy/Acetelyne Rig?

    By roscoedoh, January 24, 2006
    • 16 replies
    • 1.6k views
    • 
    • Toney
    • January 30, 2006

15. Changing Turk Thds To Large Ring

    By Ron J, March 19, 2007
    • 15 replies
    • 1.6k views
    • 
    • hodgie
    • March 24, 2007

16. Short-chambered Barrel Installation W/o Lathe Article

    By FC, March 18, 2006
    • 14 replies
    • 1.3k views
    • 
    • FC
    • March 21, 2006

17. Meier Style Floorplate Release Lever

    By donmarkey, May 27, 2007
    • 14 replies
    • 5.3k views
    • 
    • Guest
    • May 30, 2007

18. New Lathe

    By montea6b, November 3, 2009
    • 14 replies
    • 2.9k views
    • 
    • Tinman
    • November 11, 2009

19. adams & bennet short chambered barrels

    By sphingta, September 20, 2005
    • 13 replies
    • 2.8k views
    • 
    • sphingta
    • September 25, 2005

20. Lathe question

    By bubbamauser, February 17, 2006
    • 13 replies
    • 1.7k views
    • 
    • Guest
    • February 18, 2006

21. How To Open Up Feed Rails On 98 Mauser

    By The coyote, May 31, 2006
    • 13 replies
    • 5k views
    • 
    • z1r
    • June 3, 2006

22. M98 Magnum Conversions

    By manureman, September 8, 2006
    • 13 replies
    • 2k views
    • 
    • manureman
    • September 12, 2006

23. 1891 In Progress

    By Doble Troble, January 11, 2007
    • 13 replies
    • 1.3k views
    • 
    • ken98k
    • January 16, 2007

24. Mauser Rebarrel - Part 2, Chambering

    By Clemson, February 19, 2007
    • 13 replies
    • 5.5k views
    • 
    • z1r
    • March 10, 2007

25. How Not To Drill Your Receiver

    By z1r, January 9, 2008
    • 13 replies
    • 2.7k views
    • 
    • z1r
    • January 13, 2008