okie edge Posted June 17, 2009 Report Share Posted June 17, 2009 Found a worked over rifle in a pawnshop. Two holes front and aft, crappy sights, and the ugliest thumbhole stock that I have ever seen. A nice bannered mauser on the front ring. Modell-Mauser on the side rail. Stepped barrel. Turned down bolt that may have been after the fact. 8x57. Not rusty. My question is this. If one of the front holes caught the lug seating face: Is it repairable and is it worth doing to salvage the action? They will sell at 150 to 175. Will this make a nice sporter; say 280? thanks M Quote Link to comment Share on other sites More sharing options...
sonic1 Posted June 18, 2009 Report Share Posted June 18, 2009 you say if it caught .i would pass on it..are you just looking at the worst case ? what area do you live in..? Quote Link to comment Share on other sites More sharing options...
okie edge Posted June 18, 2009 Author Report Share Posted June 18, 2009 you say if it caught .i would pass on it..are you just looking at the worst case ? what area do you live in..? Waaaay down in the far southeast corner. How about you? Quote Link to comment Share on other sites More sharing options...
tinkerfive Posted June 19, 2009 Report Share Posted June 19, 2009 My question is this. If one of the front holes caught the lug seating face: Is it repairable and is it worth doing to salvage the action? Without making any recommendation, the final decision is always yours, a few random thoughts. Sounds like the buy in is pretty reasonable, do your best negotiation. If it doesn't work out you haven't lost much and have gained experience. If properly placed at 12:00 even if too far to the rear so as to "nick" the locking lug, the top lug is the one that mates to the lug with the ejector split so no force is applied when fired for the width of the ejector slot which also is at 12:00 when the bolt is closed / locked. You would want to remedy any 'burr' that a nick might leave. You wouldn't want to mar the bolt lug as it is rotated into and out of the lock position. You will need to pull the barrel to evaluate the above. You'll want to evaluate the width of the "nick" Vs the width of the ejector slot. Oh! Yes and you may get lucky. This happened to me. I drilled a hole too far to the rear but my drill bit and tap never even scratched the lug face. The rear of the hole is right into the 'bevel' where the lug transitions into the outer wall of the receiver. You pays your money, you takes your chances. Best of luck, keep us posted Tinker Quote Link to comment Share on other sites More sharing options...
okie edge Posted June 19, 2009 Author Report Share Posted June 19, 2009 Thanks for the replies fellas; another question if I can. How does the workmanship and finish on this series of Mauser compare with say, an 09 Argentine or a 1910 Mexican? m Quote Link to comment Share on other sites More sharing options...
sonic1 Posted June 19, 2009 Report Share Posted June 19, 2009 i'M in duncan , as for the 09 or 1910 thats for others here to say Quote Link to comment Share on other sites More sharing options...
okie edge Posted June 20, 2009 Author Report Share Posted June 20, 2009 i'M in duncan , as for the 09 or 1910 thats for others here to say hi Duncan.....Broken Bow here!! Quote Link to comment Share on other sites More sharing options...
okie edge Posted June 28, 2009 Author Report Share Posted June 28, 2009 Went by the pawn shop again fri. Tried to talk myself into it. Could'nt do it. It WAS a nice gun at one time. Matching #'s . The barrel was junk, two off center holes into the bore. Eleven, count em; eleven holes drilled and tapped in the reciever. At least three different sizes. the search goes on. okie Quote Link to comment Share on other sites More sharing options...
Paul Stuart Posted July 23, 2010 Report Share Posted July 23, 2010 <!--quoteo(post=44061:date=Jun 19 2009, 01:45 PM:name=sonic1)--><div class='quotetop'>QUOTE (sonic1 @ Jun 19 2009, 01:45 PM) <a href="index.php?act=findpost&pid=44061"><{POST_SNAPBACK}></a></div><div class='quotemain'><!--quotec-->i'M in duncan , as for the 09 or 1910 thats for others here to say<!--QuoteEnd--></div><!--QuoteEEnd--> hi Duncan.....Broken Bow here!! Hey Okie Im in Valliant. I think we've met before Quote Link to comment Share on other sites More sharing options...
pacrat Posted July 28, 2010 Report Share Posted July 28, 2010 Dang! 11 holes in reciever. Do you fellas have steel eating termites back there in Okiehoma? Quote Link to comment Share on other sites More sharing options...
Guest okie edge Posted August 3, 2010 Report Share Posted August 3, 2010 hey Valliant; Did you make the little gun show at hugo a couple weeks back. Had two pretty nice agentines with matching numbers. He was proud of them too. 450 ea. take care m Quote Link to comment Share on other sites More sharing options...
Paul Stuart Posted August 5, 2010 Report Share Posted August 5, 2010 No I missed it. Couldnt afford anything then anyway . Maybe next time Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.